Minelab X-Terra 705 Manuale delle Istruzioni

Instruction Manual

1617detector audioa simple detecting exerciseTarget Response (Metal Object Response) This is the sound given by the detector when a target is located

1819prospecting modecoin & treasure modeCoin & Treasure Mode is used for detecting valuable objects including old and modern coins, jewellery

20target idBuried metal objects are referred to as targets. Target signals contain ferrous and conductivity information.As the coil is passed over a t

2223preset discrimination patternsThe X-Terra 705 has an All Metal Pattern, four preset Discrimination Patterns and Iron Mask.The combinations of acce

The Preset Discrimination Patterns may be edited to create custom patterns. Method 1 – to reject a specic Target ID using an actual targetWhen a tar

To toggle between Pinpoint Auto and Pinpoint Sizing modes: Press Pinpoint to go into Pinpoint mode Press and hold Pinpoint for approx. 3 seconds

28 29adjusting menu settingsmenu operationDetection (display state) In Coin & Treasure Mode, the Target ID, discrimination segments and depth auto

30 31adjusting sensitivitysensitivityThe X-Terra 705 is highly sensitive and has a wide Sensitivity adjustment range. It is important to set the corr

32 33choosing a noise cancel channelnoise cancelThe detector may become noisy or erratic due to electrical interference from powerlines, electrical eq

34 35threshold adjusting thresholdThreshold is the constant background sound produced by the detector to help distinguish between desirable and undesi

1contents28 Menu Operation 29 Adjusting Menu Settings30 Sensitivity 31 Adjusting Sensitivity32 Noise Cancel 33 Choosing a Noise Cancel Channel34

36 37volumeVolume is the level of sound emitted by the detector when a target is detected. The Volume control limits the maximum volume of target sig

38 39adjusting tonestonesTarget TonesThe number of Target Tones may be selected from the Tones menu. There are ve dierent options listed in the tabl

40 41ground balanceThe X-Terra 705 is capable of operating in two dierent types of grounds, magnetic (e.g. inland parks and goldelds) and conductive

When Pinpoint is activated, Tracking Ground Balance is automatically disabled. When Pinpoint is deactivated, Tracking Ground Balance is automatically

44 45battery behaviourtracking ground balance offsetThis setting is recommended for experienced users.Tracking GB Oset allows you to set the Tracking

46factory presets Patterns Factory Preset Custom patterns are saved when the X-Terra 705 is switched o. To erase custom patterns and return to p

The X-Terra 705 is capable of operating at three dierent transmission frequencies set by VFLEX compatible coils.Concentric Standard (7.5kHz) This fre

50soundsA trowel, knife or small spade are good tools for recovering targets. Once a target has been located, clear the surface of loose material and

5253accessoriesWhen not using headphones, keep the rubber cover closed to protect the control box electronics from moisture and dust.The use of headph

5455x-terra 705 specificationsTransmission Single Frequency Sine Wave Technology VFLEX Coil Standard 9” Concentric 7.5 kHz Visual Display Transec

23how detectors workMetal detectors create an electromagnetic eld, which penetrates the ground. Metal objects cause a change to this eld because the

56service and repair formOwners NameAddressTelephone Day ( ) Home ( )Fax ( )Email Todays DateDetector / ModelSerial NumberPurchased FromPurc

Minelab Electronics Pty LtdPO Box 537, Torrensville Plaza Adelaide, South Australia, 5031 Australia Tel: +61 (0) 8 8238 0888 Fax: +61 (0) 8 8238 0890

Connecting the Coil Plug the two rubber washers into the holes on either side of the lower shaft yoke. Slide the yoke into the yoke bracket on top

Coil Cable Assembly Wind the coil cable around the lower and middle shaft enough times to take up the slack. Use the velcro tabs to keep the coi

89keypad layoutPatterns Scrolls through the dierent Discrimination Patterns (Coin & Treasure Mode only).Power Turns the detector On/O. All Meta

1011lcd layoutGround Balance can only be accessed via the Ground Balance button. (Ground Balance, p. 40)Patterns Preset Discrimination Patterns are

1213turning the detector onIt is recommended to only turn the detector on, when outdoors, away from sources of electromagnetic disturbance.There are m

1415sweeping the coilholding the detectorTo hold the detector, thread your arm through the armrest and strap. Grasp the handle of the detector and res